Z-AXIS Expands Custom Wire and Cable Assembly Production
September 18, 2020 | Z-AXISEstimated reading time: 1 minute
Z-AXIS, Inc. has expanded its production capacity for custom cable assemblies and wire harnesses, with a $40,000 investment in automated production and test equipment at its contract design and manufacturing center near Rochester, NY. The new equipment includes a Panduit CP Series ferule crimp press, a Kingsing KS-W66 Series heavy duty rotary cable stripper, a Gamma Mark III Plus heat shrink label printer, and a CableEye continuity tester.
“Custom cable assemblies and wire harnesses are essential for commercial, industrial and medical electronic equipment,” said Michael Allen, President of Z-AXIS. “With continuous investment in automation we boost capacity and throughput, keep costs down for our customers, and continue to meet high quality standards. Whether it’s cable assemblies, printed circuit board assemblies (PCBAs) or full box build services, we support leading customers with electronics manufacturing in the USA.”
The Panduit ferule crimp press supplements existing AMP K presses. It automates wire stripping, ferrule placement, and ferrule crimping with an average cycle time of less than 1.5 seconds. The programmable system with vibratory-bowl feeder accommodates loose-piece ferrules from 24 to 12 AWG. Integral wire stripping eliminates the need to use pre-stripped wire, saving a step and preventing the installation of ferrules onto any turned-back strands, which can result when using pre-stripped wire.
The Kingsing rotary cable stripper is optimized for co-axial, tri-axial, and other multi-layered cable stripping in up to nine layers. It supports full stripping, half stripping, middle stripping and twisting. It is easily programmable for cable diameter, stripping length and pull-off length. Precision cable centering and rotary blades delivery highly accurate cutting, removing the insulation close to the conductor for reduced pull-off force. It supports complex cable assembly production with high processing speeds.
The Gamma label printer prints on heat shrink tubing at high speeds, up to 11 inches per second, and cuts the tubing to specifications. The tubing is then applied to cables from 1/16” to 2.5” in diameter. High-resolution printing clearly identifies cables, while the heat shrink tubing can be used to provide strain relief.
The CableEye test system checks basic continuity and detects opens, shorts, mis-wires and intermittent connections in a wire harness or cable assembly. It features 128 test points and handles cables with up to 64 conductors. The test bed accommodates more than 200 standard connector types
Suggested Items
Real Time with… IPC APEX EXPO 2024: Circuit Board Testing Strategies and the Impact of AI
05/08/2024 |Editor Marcy LaRont speaks with Bert Horner, president of The Test Connection, about the importance of strategic planning and design-for-test (DFT). Bert touches on some common mistakes that occur when DFT is not adequately considered early on. The discussion outlines an overarching industry need for a culture shift toward increasingly higher levels of integration and collaboration. Bert mentions that AI now has an influence on testing, as everywhere else, and announces his forthcoming book.
Real Time with… IPC APEX EXPO 2024: Understanding Objective Evidence in Manufacturing Processes
05/07/2024 | Real Time with...IPC APEX EXPOGraham Naisbitt explains the importance of objective evidence in manufacturing processes, debunking the common misconception that the ROSE test is a cleanliness test. He also discusses the introduction of Rev J, a requirement for measuring ionic contamination on circuit assemblies, and the challenges in accurately measuring contamination. Alternative methods like ion chromatography and the need for updating standards like the ROSE test are mentioned.
U.S. Air Force Secretary Kendall Flies in AI-Piloted X-62A VISTA
05/06/2024 | Lockheed MartinLockheed Martin Skunk Works joined the U.S. Air Force Test Pilot School and other government and industry partners in hosting U.S. Secretary of the Air Force Frank Kendall to fly in the X-62A Variable In-flight Simulation Test Aircraft (VISTA), a one-of-a-kind aircraft modified to test artificial intelligence (AI) and autonomy capabilities.
Real Time with… IPC APEX EXPO 2024: Software Solutions for Circuit Board Challenges
05/03/2024 | Real Time with...IPC APEX EXPONolan Johnson speaks with Will Webb from Aster Technologies about their software solutions for design teams, manufacturing, test engineers, and process engineers. Aster's software addresses the increasing complexities of circuit boards and the need for alternative testing methods.
Manta Ray UUV Prototype Completes In-Water Testing
05/02/2024 | DARPAThe Manta Ray prototype uncrewed underwater vehicle (UUV) built by performer Northrop Grumman completed full-scale, in-water testing off the coast of Southern California in February and March 2024.