HDI Design Education: Is Anyone Interested?


Reading time ( words)

I first became aware of high-density interconnection (HDI) design methodology in 1997 when a co-worker of mine came back from a training class that was taught by Happy Holden. “Little Dave” (since our department had two employees named David W.) came back excited to try this new design knowledge on a multilayer board stackup that only used blind and buried vias, with no through-hole vias. His excitement and dedication paid off, as he completed the design with an autorouter exactly as he planned. Through Dave’s success, our department then started to create other designs using HDI stackups that were taught in Happy’s class and our autorouter tool.

I did a few complex designs that fit into the IPC Type III category. One of the more complex designs I attempted could only autoroute up to 98% completion after trying many setup files (with great assistance from “Big Dave”) and our most powerful computer available within our group. I finished the design manually, and the board was fabricated and worked as designed.

About six months later, when we upgraded our department’s autorouter computer, I restored the design from archive, and re-ran the last autorouter configuration file on that 98% completed design. This time, the design was now 100% completely autorouted, and took about a third less time than on the previous “most powerful” computer. This one little re-investigation became the catalyst for my full immersion into HDI design research, reviewing the existing designs and now trying newer autorouting approaches with a variety of more challenging stackups, via spans, and via sizes. Each new redesign attempt created more curiosity to push autorouters and stackup methodologies to their absolute limits.

Over the next few years, any article written on HDI that crossed my path became assimilated into my mental database. I met Mike Fitts lecturing on HDI at a design conference, and I asked him to clarify my repository of HDI re-design questions. When Mike and I met at another design conference, he introduced me to the very person who inspired Little Dave: Happy Holden.

Read the full column here.


Editor's Note: This column originally appeared in the May 2014 issue of The PCB Design Magazine.

I first became aware of high-density interconnection (HDI) design methodology in 1997 when a co-worker of mine came back from a training class that was taught by Happy Holden. “Little Dave” (since our department had two employees named David W.) came back excited to try this new design knowledge on a multilayer board stackup that only used blind and buried vias, with no through-hole vias. His excitement and dedication paid off, as he completed the design with an autorouter exactly as he planned. Through Dave’s success, our department then started to create other designs using HDI stackups that were taught in Happy’s class and our autorouter tool.

I did a few complex designs that fit into the IPC Type III category. One of the more complex designs I attempted could only autoroute up to 98% completion after trying many setup files (with great assistance from “Big Dave”) and our most powerful computer available within our group. I finished the design manually, and the board was fabricated and worked as designed.

About six months later, when we upgraded our department’s autorouter computer, I restored the design from archive, and re-ran the last autorouter configuration file on that 98% completed design. This time, the design was now 100% completely autorouted, and took about a third less time than on the previous “most powerful” computer. This one little re-investigation became the catalyst for my full immersion into HDI design research, reviewing the existing designs and now trying newer autorouting approaches with a variety of more challenging stackups, via spans, and via sizes. Each new redesign attempt created more curiosity to push autorouters and stackup methodologies to their absolute limits.

Over the next few years, any article written on HDI that crossed my path became assimilated into my mental database. I met Mike Fitts lecturing on HDI at a design conference, and I asked him to clarify my repository of HDI re-design questions. When Mike and I met at another design conference, he introduced me to the very person who inspired Little Dave: Happy Holden.

Read the full column here.


Editor's Note: This column originally appeared in the May 2014 issue of The PCB Design Magazine.

Share


Suggested Items

AltiumLive Summit—Munich, Germany, Part 1

11/07/2017 | Pete Starkey, I-Connect007
Altium held a very successful AltiumLive PCB Design Summit in San Diego, California at the beginning of October for the benefit of their North American design community, and followed it three weeks later with a counterpart European event in Munich. And what an eye-opener it proved to be—literally hundreds of delegates, a superbly organised and managed programme, billed as a completely immersive two-day interactive design experience on a theme of learning, connecting and getting inspired.

Insulectro Teams with Isola to Address Signal Integrity Needs

11/06/2017 | Andy Shaughnessy, PCB Design007
Insulectro and Isola recently shared a combined booth during PCB West 2017. Insulectro has distributed Isola materials for years, and the companies wanted to focus on Isola’s line-up of high-speed, low-loss material sets. Insulectro’s Chris Hunrath, VP of Technology, and Norm Berry, Director of Laminates and OEM Marketing, sat down with me to discuss the challenges facing signal integrity engineers today, and some of the Isola low-loss, low-Dk materials that can help with their signal integrity requirements. You might find Chris and Norm speaking to a group of PCB designers near you.

Stephen V. Chavez Talks Mil/Aero PCB Design

08/14/2017 | Andy Shaughnessy, PCBDesign007
Stephen V. Chavez, CID+, is the lead PCB designer for the Electronic Systems Center division of UTC Aerospace Systems (UTAS), a military contractor that builds all manner of cutting-edge tools for the American warfigher. He’s been designing military and aerospace PCBs for decades, and he’s a veteran of the United States Marine Corps. I caught up with Steph and asked for his thoughts on designing PCBs for the military and aerospace markets.



Copyright © 2017 I-Connect007. All rights reserved.